Vermiculite Insulation

What it is

Vermiculite is a mica like mineral mined around the world and used in variety of commercial and consumer products because of its fire resistance and good insulating properties.

What it problem

Some vermiculite insulation may contain amphibole asbestos fibres. These can cause health risks if disturbed during maintenance, renovation or demolition. The vermiculite of concern is basically which is mined by the Libby mine in Montana from 1920 - 1990. It was sold as Zonolite attic insulation and possibly other brands. Vermiculite from Libby mine may contain amphibole asbestos. Vermiculite insulation from the Libby mine was not used widely after mid 1980 and were not sold in Canada after 1990. Not all vermiculite insulation produced before 1990 contains asbestos. However, if the building is old and contains vermiculite insulation than it should be tested in the lab for asbestos to be safe.

What can be Done

There is mostly no danger or health  risk if the insulation is sealed behind wallboards and floorboards, isolated in an attic, or otherwise kept from exposure to the interior environment. The overall percentage of amphibole asbestos is very less in bulk vermiculite but they can increase the material is disturbed.

If there is vermiculite insulation in your attic take following precautions!

1. Avoid disturbing Vermiculite insulation.

2. Don't allow children to play in the attic and inform anyone working in the   attic about vermiculite insulation.

3. do not use attic for storage.

4. Avoid going and moving in attic if required use walk on boards.

5. Use respirator masks only and not dust masks.

6. If you decide to remove the vermiculite insulation or remodel / renovate your house use certified and qualified contractor trained in its removal only. Never try to remove it yourself.

7. Seal all cracks and holes in the ceilings of rooms below the insulation i.e apply caulking around light fixtures and attic hatch to prevent insulation sifting through.

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham, Home Inspection Milton

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga

All you need to know about Asbestos in your Home

What it is

Asbestos is the generic name for variety of fibrous minerals found naturally. It can only be identified under special type of microscope. Asbestos was added to many products in the past to strengthen them and to provide insulation and fire resistance.

What are the risks

Breathing high levels of Asbestos can cause cancer of lungs (Mesothelioma)  and can cause scarring of the lungs. The risk increases with the amount of asbestos fibres inhaled and duration of exposure. Furthermore, people who smoke are at higher risk than non-smokers. The symptoms of the disease usually does not appear until 20 to 30 years of first exposure to asbestos. Most people exposed to small quantities of asbestos in their daily lives do not develop any problems.

Where it can be found in a Home

Asbestos is usually found in older homes in!

. Roofing and siding

. Insulation (Attic, hot water pipes etc)

. Textured paints, patching compounds

. Old stove pads

. Vinyl floor tiles and backing on vinyl sheet flooring and adhesives

. Hot water pipes insulation and tapes.

. Oil and coal furnaces and door gasket.

. Roofing tiles

How to identify it

Asbestos can't be identified visually. if in doubt contact certified professional, who will take samples to be analysed in the laboratory. Asbestos fibres can only be detected under special microscope.

What needs to be done about it

Don't panic if you think asbestos is present in your house. The best thing to do is not to disturb asbestos material. Asbestos material in good condition will not release asbestos fibres. There is not much danger unless asbestos is disturbed and fibres are released. Check material regularly if you suspect it may contain asbestos. Don't touch it, but look for signs of wear or damage, such as tears, abrasions or water damage. Damaged material may release asbestos fibers. Consult with asbestos certified professional for further evaluation and advise and if and when you plan to do any remodelling or construction in your house.

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Winter Home Maintenance Tips

Before winter arrives prepare your home for the harsh conditions of this weather. Here are some winter home maintenance tips for the cold temperatures ahead.

• Get your furnace serviced by the Certified HVAC technician to ensure its properly running and to avoid any breakdown during peak winter.

• Check, clean and replace furnace filter if required.

• Winterize your house by closing the shut off valves for outside Hose bibs from inside the house and then draining the all the water out between inside shut off valve and outside Hose Bib to prevent bursting of the pipe causing basement flooding.

• Make sure the attic is properly ventilated and insulated to prevent development of ice damns in winter. 

• Monitor your home for excessive moisture levels which can cause significant damage over time and pose serious health problems and take corrective action if necessary.

• All exposed water pipes in cold areas, such as attics, garages, and crawlspaces, should be insulated.

• Examine windows, doors and attic for ice or frost accumulation or cold air leaks.

• Clean humidifier two or three times during the winter season.

• The chimney should be inspected for nesting animals trying to escape the cold.

• Patio furniture should be covered.

• If there is a deck, it might need an extra coat of sealer.

• Repair / fill any small cracks in bricks and foundation wall. Ice has more volume than water any water in the cracks will expand when changed to ice, making the crack bigger.

• Get your annual Home Inspection done by the Qualified Home Inspector to identify any other areas of concern which needs your attention.

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs
1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Damns
6. Common Electrical problems in a House
7. Aluminum Wiring
8. Winter Home Maintenance Tips
9. Issues affecting older Homes from Insurance point of view
10. Causes of Wet Basement

Issues Affecting Older Homes for Insurance Coverage

If you are buying a house older than 30 years it’s always a good idea to speak to your insurance company before finalizing the deal. Insurance companies may ask you to upgrade one and more components of your house before providing you with the insurance coverage. You may need to budget the upgrades in the purchase offer you make for the house.

There are many items to look out for but the main areas of concern are!

1. Oil fuel Tank

Oil fuel tanks if leaking can cause Environmental Hazard which can cost enormous amount of money to clean up. The oil tanks older than 25 years have a higher potential of developing rust and thus leaking oil. Most Insurance companies require the tank to be inspected by Technical Standards and safety Authority (TSSA) inspector. Furthermore, if the oil tank is very old the insurance company may ask to get it replaced with a gas or electrical furnace before insuring your home.

2. Wood burning stoves

Wood burning (solid fuel) burning stoves can pose a very serious fire hazard and a health Hazard as they can generate carbon monoxide if not properly vented or installed. Insurance companies may ask the stove should be inspected by Wood Energy Technical Training (WETT) Technician and certified by Underwriters Laboratories of Canada (ULC), Canadian Standard Association (CSA) or Warnock Hersey before providing insurance coverage. Furthermore, the stove should be cleaned and inspected yearly by Professional sweep to check the chimney liners for development of creosote and any cracks, which can be a Fire Hazard.

3. Knob and tube wiring

Knob and tube wiring is mostly found in houses older than 50 years. its consists of parallel hot (black) and neutral (white) wires, separated by knobs (or insulators) and ceramic tubes.

Knob and tube wiring is considered a higher risk wiring than the modern wiring installation because.

a. There is no ground wire thus it’s a safety hazard. also since the receptacles are two prongs many modern equipment will not be able to connect and the prongs needs to be replaced by GFCI protected Three prong outlets, or the wiring has to be changed to modern Romex (three wire) wiring.

b. Giving their age, the wires are highly susceptible to wearing and exposure, presenting a serious safety hazard. The wires can also be covered by insulation at some locations which can result in overheating and is a Fire Hazard.

c. The accidental contact of hot and neutral wires may potentially cause a electrical fire.

The insurance company may ask to replace the Knob and Tube wiring or alternatively ask to get it inspected by licensed electrical contractor for safety before insuring your home.

4. 60-Amp Electrical Service

60-Amp service was prevalent in the homes built prior to 1950. This service may not be sufficient to run modern equipment in the house. There is a chance of overloading and overheating the panel which is a major Fire hazard. Insurance companies may require you to upgrade the service to 100-Amp which is a standard for modern homes or to install a switching devise that allows for the operation of only one major appliance at a time.

5. Galvanized Steel Plumbing

Galvanized steel pipes, commonly installed in homes prior to 1950, have an average life expectancy of 40–50 years. Over time, the galvanized steel pipes begin to rust or corrode from the inside out, resulting in reduced water pressure and restricted water flow. This presents an increased risk of leaks or ruptures occurring in the pipes and the potential for flood damage. Your insurance company may require you to replace galvanized steel piping with copper and plastic piping before providing you with insurance coverage.

 

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs

1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Damns
6. Common Electrical problems in a House
7. Aluminum Wiring
8. Winter Home Maintenance Tips
9. Issues affecting older Homes from Insurance point of view
10. Causes of Wet Basement

 

Aluminum wiring

Utility companies have used Aluminum in their transmission lines since early 1900. It is still the preferred transmission and distribution wiring material for distributing companies because Aluminum offers cost and weight advantages over copper.

This blog is focussed on Aluminum wiring from Home Inspection point of view thus we will talk about its use in houses only.

In North America Aluminum wiring was used in houses between 1960 and late 1970. The cost of copper was much higher compared to aluminum. Therefore, to save money Aluminum was used as an alternative to copper. It is estimated that there are around 450,000 houses in Canada which are wired with Aluminum wiring. Insurance companies are becoming more and more wary of the houses with aluminum wiring due to associated fire hazard and require inspection and a certificate of safety from the licensed electrician before issuing or renewing insurance policy for the houses with Aluminum wiring. As per US product safety commission Homes with aluminum wiring are 55 times more likely to have one or more connections reach Fire Hazard Condition than a home wired with copper.

Problems with Aluminum wiring

1. Aluminum wire in itself is not a fire hazard its only when the termination were not properly done it becomes loose, overheat which can cause arching which can start the fire.

2. Aluminum oxidises more than copper which forms a layer of aluminum oxide on top of wire. The layer although very thin is non-conductor of electricity. The current carrying capacity of the wire is then reduced which overheats the wire.

3. Aluminum expands and contracts more than copper so if the connections are not made properly overtime the connections become loose and arching can occur.

4. The problem in aluminum wiring is mostly for the single strand wiring circuits used for 15amp and 20 amp branch circuits, although all the circuits need to be inspected by licensed electrician.

5. Aluminum has a higher resistance to current flow which means to carry same amount of current aluminum wire has to be thicker than that of copper.

6. Aluminum is more malleable thus it is more sensitive to compression. If the screw has been over-tightened on Aluminum wiring, the wire will continue to deform after tightening has stopped. This deformation creates a loose connection and reduces the current carrying capacity of the wire.

How to locate aluminum wiring

The best place to check whether your house has Aluminum wiring is to look for visible wiring in attic, basement and crawl space or at the service panel. The wiring should be marked with the word Aluminum, ALUM, AL, ALUM ACM, AL ACM. During home inspection the inspector will open the main distribution panel (if accessible and safe). Aluminum wires can be spotted at splices near the breakers or fuses.

Furthermore, following symptoms that indicates aluminum wiring!

1. Flickering lights.

2. Static on the radio, computer or TV

3. Circuit breakers or fuses that trip for no apparent reason.

4. Odor similar to that of burning plastic around switches and receptacles.

5. Discolored or warm switch plates and receptacles covers.

6. Plugs that do not work even with the circuit energized.

How to fix Aluminum wiring problems

To fix aluminum wiring problems hire Licensed Electrical contractor to inspect your house and to get advise about what needs to be done to ensure the safety. Every house is different and the solution to the aluminum wiring varies. 

Following is few fixes that a licensed electrical contractor can propose!

1. The best and permanent solution is to replace Aluminum wiring with the copper wiring.

2. Cut back the damaged aluminum conductors and join these to a copper tail using a connector approved for use with aluminum. Such connectors are colored brown or purple (depending on the manufacturer). The copper tail is then terminated at the terminal screws of an ordinary devise (which includes approved receptacles, etc.)

3. Cut back damaged aluminum conductors and re-terminate a new device bearing the marking CO/ALR (copper aluminum revised).

At RK Home Inspection we advise our clients to hire a licensed electrical contractor to inspect and advise on the adequacy of Aluminum wiring.

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps  Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs

1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Damns
6. Common Electrical problems in a House
7. Winter Home Maintenance Tips
8. Issues affecting older Homes from Insurance point of view
9. Causes of Wet Basement

 

Common Electrical problems in a House

No one disputes the importance of properly inspecting the Electrical systems of the house during the Home Inspection. Faulty electrical systems can not only result financial impact to a home buyer it is also a major safety concern. Unlike other systems electrical system may still function even if it was not properly installed. It can easily cause fire, shock and other problems which can result in a significant damage to property and in worst cases loss of life. The qualifications, experience and knowledge of Home Inspector is tested to its full extent while checking electrical systems.

In this blog I will just mention various defects and write about them in detail in the following blogs.

Common electrical wiring defects found in a house are!

1. Open Ground

This is a problem which is more common in old houses. The electrical outlets are not grounded which can be a safety hazard as it can result in a shock.

2. Reverse polarity

Most three prong electrical outlets have three wires Hot, Neural and Ground. If the Hot and neutral are reversed the condition is known as reverse polarity.

3. False Ground

This is very difficult to detect. In this case neutral is connected to the ground which makes entire outlet hot or charged. If you bring your voltage tester near the outlet it can be easily observed.

4. Disconnected Neutral

5. Hot wire connected to ground wire terminal

6. Missing or malfunctioning GFCI and in New Construction AFCI (for detailed information regarding GFCI receptacle refer my previous blog on that subject).

7. Presence of Aluminum wire in the House

Presence of Aluminum wire normally scare a lot of buyers. Aluminum wire in itself is not a problem. It is only at its termination that it requires special treatment or outlets to prevent oxidation and arching. Aluminum wire problems are mostly for 15 amps or 20 amps circuits.

8. Presence of old knob and tube wiring

9. Missing cover plates at the junction boxes or outlets

10. Presence of 2 wires under the breaker (double tapping).

11. Incompatibility of wire gauge and breaker amps. e.g. 14 gauge wire for 15 amp breaker and 12 gauge wire for 20 amp. breaker.

12. Compatibility between the appliance current requirement and the breaker feeding it e.g. 40 amp. breaker for stove is required use less and the breaker will trip frequently.

13. Proper wiring inside the Main electrical panel and the sub panel.

We can just go on writing on this subject for ever. The above mentioned defects are the most common we encounter during a typical Home Inspection.

At RK Home Inspection we are experienced, Certified and Qualified to detect electrical systems problems. We carry GFCI, AFCI tester along with millimetre and infrared thermometer.

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs

1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Damns
6. Aluminum Wiring
7. Winter Home Maintenance Tips
8. Issues affecting older Homes from Insurance point of view
9. Causes of Wet Basement

Causes of Wet Basement

One of the major problems I have encountered during Home Inspection is water leakage in the basement. Basement is basically a depression in the earth, if it’s not properly constructed or maintained, over time it will leak.

The best way to prevent water penetration in basement is to eliminate the conditions which are causing water to come in contact with foundation and to divert it away by using proper grading.

The biggest contributing factors for leaky basements are!

1.   Improper grading around the house

Lack of proper grading is simply the largest contributing factor to leaky basement. The landscaping around the house should be such that it enables water to flow away from the house. It is recommended that the grade adjacent to the foundation should be sloped 1:10 away from the foundation. If it is not achievable due to site conditions, swales should be constructed along the perimeter to gather water and direct and discharge it away from the foundation.

2.   Downspouts are not extended away from the house

The downspouts should not discharge storm water close to the foundation wall. It is recommended that the downspouts are extended about 4 feet to 6 feet away from the foundation wall and have splash pads.

3.   Basement windows sill too close to grade

It is recommended that basement windows sill should be around 8 inches higher the adjacent grade to prevent water penetration in basement due to snow accumulation and water.

4.   Deteriorated parging on the foundation wall

Foundation wall needs periodic maintenance if the parging on the foundation wall is peeling off or is deteriorated it needs to be repaired immediately.

5.   Cracks in foundation wall

Cracks can develop in foundation wall due to variety of reasons. However, if they develop they should be repaired immediately by qualified contractor to prevent further damage and water penetration in the basement.

6.   Poorly constructed foundations and basements

Sometimes the foundation wall and slab on the grade are not properly waterproofed. Furthermore, the drainage tile in the perimeter which is required to collect water and discharge it away is not present, is clogged or not properly installed. This will enable water to accumulate near foundation wall and will eventually leak inside.

At RK Home Inspection we check thoroughly your house grading, foundation cracks and other contributing factors to protect and provide you with honest reporting enabling you to take and informed decision.   

At RK Home Inspections we are available 7 days a week and we serve entire GTA Home Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA, Home Inspection Markham

Find us on google places / maps  Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs

1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Damns
6. Common Electrical problems in a House
7. Aluminum wire
8. Winter Home Maintenance Tips
9. Issues Affecting Older Homes for Insurance Coverage

Ice Dams

How they are formed?

Ice dams are formed when the snow on the roof is melted by the heat escaping out from the house or by the action of sun. The melting occurs mostly at the roof and not at the projected eaves. Water from the melting snow can then freeze and form ice dams at the eaves trough and roof overhang. This ice will prevent and block the water from the melted snow to flow to the gutters. The water then finds it way under the shingles and thus leaking into the attic.

 

What problems they cause?

·         The main problem caused by ice dam is the water penetration into the attic and thus causing water damage at various areas of the house.

·         Rotting of roof sheathing, walls, framing and peeling paint.

·         Mold growth which can result in various respiratory illnesses.

·         The R value which measures the resistance of the insulation for transmission of heat is also reduced when insulation is wet. This will further deteriorate the thermal performance and more heat from house will leak to the roof. This will result in more ice dams.

 

 

How to prevent its formation?

·         Roof should be properly vented to keep the underside of the roof cold and also to remove the heat which has leaked into the attic from the house.

·         Increase the thickness of insulation in the attic

·         Properly seal all the openings and penetration from the house to attic sealing to prevent heat from leaking into the attic.

·         Install vapour barrier under the insulation facing downwards towards the room to prevent water vapour escaping into the attic.

·         Extend exhaust systems that terminates just above the roof, to prevent melting of the snow.

·         There should be minimum three inches of gap between the insulation and the roof sheathing at the sloped roof areas.

 

At RK Home Inspections we are available 7 days a week and we serve entire GTAHome Inspection Toronto, Home Inspection Mississauga, Home Inspection Brampton, Home Inspection Vaughan, Home Inspection GTA

Find us on google places / maps Home Inspection Mississauga, Home Inspector Mississauga, Mississauga Home Inspection

Related Blogs

1. RK Home Inspections
2. GFCI Outlet?
3. What is Home Inspection?
4. Dangers of Carbon Monoxide.
5. Ice Dams
6. Common Electrical problems in a House
7. Aluminum wire in a house
8. Issues affecting older Homes from Insurance point of view
9. Causes of Wet Basement